2012年12月21日星期五

Danfoss Frequency Converters VLT® AQUA Drive FC 202


VLT® AQUA Drive FC 200

VLT® AQUA Drive FC 202

Danfoss VLT® AQUA Drive is dedicated to water and wastewater applications. With a wide range of powerful standard and optional features, the VLT®AQUA Drive provides the lowest o...

Features and benefits

Power and voltage range
200-240 V.....0.25 kW - 45 kW
380-480 V.....0.37 kW - 1000 kW
525-600 V.....0.75 kW - 90 kW
525-690 V....11 kW - 1.4 MW
Three phase3*200-240V… 0.25 - 45 kW
3*380-480V… 0.37 - 1000 kW
3*525-600V… 0.75 - 90 kW
3*525-690V… 11 - 1.4 MW

Single phase 1*200-240V 1.1 - 22kW
1*380-480V 7.5 - 37kW
EnclosuresIP20/chassis, IP21/NEMA 1, IP55/NEMA 12 and IP66/NEMA 4X

Dedicated water features Auto tuning of the PI controllersWith auto tuning of the PI controllers, the drive monitors how the system reacts on corrections made by the drive - and learns from it, so that precise and stable operation is achieved quickly.

Automatic Energy Optimization
The standard feature AEO provides optimized motor magnetization at all speeds and loads. This increases energy efficiency by 5-15% for partial loads.

Energy monitoring  
The VLT AQUA Drive provides a complete range of energy consumption information, which helps identify low-efficiency components in the system.

PM motor support
Support for any non salient permanent magnet motor up to 22 kW for better system efficiency.



Features and benefits

 
Pipe Fill ModeEnables controlled (closed loop) filling of pipes. Prevents water hammering and bursting water pipes, or blowing off sprinkler heads.

End of Pump Curve detects breaks and leakage
The feature detects breaks and leakage. End of curve triggers an alarm and shuts off the pump, or performs another user defined action.

Dry Pump Protection lowers maintenance costs
The VLT AQUA Drive constantly evaluates the condition of the pump based on internal frequency/power measurements.

Deragging
Can be used as a proactive or reactive feature of the AQUA Drive for wastewater applications to prevent clogging of pumps. Deragging helps to avoid downtime and reduces maintenance cost.

Cascade controller solutionsThe built-in standard cascade controller controls up to three pumps with a fixed lead pump. The optional Extended and Advanced Cascade Controller makes it possible to extend the number of pumps and ensure smooth staging/de-staging, also in mixed pump and variable speed pump applications.

Motor AlternationThis built-in logic controls alternation between two pumps in duty/stand-by applications. Motion of the stand-by pump prevents the pump from sticking. An internal timer assures equal usage of the pumps.

Flow compensation
The flow compensation feature reduces the pressure set point according to the flow, which saves energy.

Initial/Final RampThe initial ramp provides fast acceleration of pumps to minimum speed, from where the normal ramp takes over. This prevents damage on thrust and bearings.

Check Valve Ramp
The Check Valve Ramp of the VLT AQUA Drive prevents water hammering as check valves close smoothly when the pump stops.

Quick Menu
The user-friendly Quick Menu, and its submenus of the VLT AQUA Drive, saves time during drive configuration. The submenu "Water and Pumps" provides direct access to application specific features.

SafetyThe VLT AQUA Drive can optionally be delivered with the safe torque off (safe stop) functionality suitable for category 3, performance level d according to EN 13849-1 and SIL 2 according to IEC 62061/IEC 61508. This feature prevents the drive from starting unintended.

Accessories

A wide selection of accessories is available for the VLT AQUA Drive to suit your needs. For further details see the Operation Instructions.

OptionsOptions for bus communication, user programs, etc., are delivered ready for plug and play.

Display optionsLocal Control Panel LCP (graphical and numerical)
Cable for LCP, 3 m [9,8 ft.]
Remote-mounting kit for Local Control Panel (LCP)
Blind cover

Fieldbus options
VLT PROFIBUS DP/V1 MCA 101
VLT DeviceNet MCA 104
VLT PROFINET MCA 120
VLT EtherNet IP MCA 121
VLT Modbus TCP MCA 122

I/O optionsVLT Extended I/O MCB 101
VLT Relay Card MCB 105)
VLT Extended Cascade Controller MCO 101
VLT Advanced Cascade Controller MCO 102
VLT Analog I/O MCB 109

VLT PTC Thermistor Card MCB 112
VLT Sensor Input MCB 114

Filters VLT Advanced Harmonic Filter AHF 005/010
VLT Sine-wave Filter MCC 101
VLT dU/dt Filter MCC 102
VLT Common Mode Filter MCC 105

PC software tools
VLT Motion Control Tool MCT 10 for commissioning and servicing
VLT Motion Control Tool MCT 31 for calculating harmonic distortion


Other accessories
VLT 24V external supply MCB 107
IP21/NEMA1 Kit
Kit for panel through mount
USB connection cable to PC

没有评论:

发表评论